Neumann TLM 170R MT Studio Condenser Microphone (Black)
Multi-Pattern Large Diaphragm FET Condenser Microphone
The TLM 170 R condenser microphone is a large diaphragm microphone with multiple polar patterns. Its sound has a very transparent characteristic, in contrast to some of our other microphones that have a distinct personality. Therefore, this microphone is used for many diverse applications in professional recording studios, in broadcasting, film and television, and for semiprofessional productions. The polar patterns can be selected either at the microphone itself, or controlled remotely through the special N 248 power supply.
Far from conjuring antiquated or retro nostalgia, Neumann’s industry-leading TLM 170 R embodies an imposing, contemporary studio microphone. Its wide-ranging performance spectrum and high-precision reproduction mean that the TLM 170 R is universally applicable.
The freshly designed sound transducer, which was developed exclusively for this microphone, is inspiring with its exceptional impulse fidelity. The boundless constancy of multiple polar patterns, omnidirectional, cardioid and figure-8, with the intermediate patterns wide-angle cardioid and hypercardioid, is also uncommon for a large-diaphragm capsule. The TLM 170 R offers optimal sound not only for the cardioid setting; it also guarantees maximum precision over the entire frequency range for all of the other directional characteristics. These five directional characteristics can be chosen by means of a rotary switch. In the sixth position, marked "R", the directional patterns can be manipulated remotely with the N 248 power supply. Without need of a special cable.
Transformerless circuitry enables a high degree of linearity and a large dynamic range. The self-noise of only 10 dB-A is essentially inaudible, while at the same time, the TLM 170 R features high level handling. The maximum sound pressure level of 141 dB SPL can be increased to 153 dB SPL via pre-attenuation (Pad). This makes it possible for the TLM 170 to transmit the sound of even the loudest instruments without distortion.
The pre-attenuation switch is situated to the rear of the microphone and on activation reduces transmission levels by 10 dB. Use of the switch shifts the microphone’s dynamic range by 10 dB, rather than expanding it. Therefore, its best use is to mitigate overloading following devices with excessive sound pressure levels. The other switch on the back of the microphone can be used to change the cutoff frequency of the built-in high-pass filter, so as to suppress the effects of impact sound and wind noise, or to compensate for the proximity effect.
- Local and remote controlled large diaphragm microphone
- Pressure-gradient transducer with double membrane capsule
- Five directional characteristics: omni, wide angle cardioid, cardioid, hypercardioid, figure-8
- Patented circuitry for remote and local switching of directional characteristics
- Switchable low frequency roll-off and 10 dB preattenuation
- Tiltable, elastically suspended bracket mount
Acoustical operating principle: Pressure gradient transducer
Directional pattern: Omnidirectional, wide angle cardioid, cardioid, hypercardioid, figure-8
Frequency range: 20 Hz ... 20 kHz
Sensitivity at 1 kHz into 1 kohm: 8 mV/Pa
Rated impedance: 50 ohms
Rated load impedance: 1 kohms
Equivalent noise level,: 26 dB
Signal-to-noise ratio, (rel. 94 dB SPL): 68 dB
Maximum SPL for THD 0.5%: 144 dB
Maximum SPL for THD 0.5% with preattenuation: 154 dB
Maximum output voltage: 10 dBu
Dynamic range of the microphone amplifier (A-weighted): 130 dB
Supply voltage (P48, IEC 61938): 48 V ± 4 V
Current consumption (P48, IEC 61938): 3 mA
Matching connector: XLR3F
Colour - Black
Dimensions and Weight
- Microphone TLM 170 R
- Wooden Box
- Dust Cover