Summit Audio ECS-410 Everest

Tube-Transistor Channel Strip

Summit Audio > Mic Pres, EQs & Dynamics > Mic Pre-Amps

Discontinued

Take four of the most intense, flavorful audio processing blocks and fuse them into one master channel strip. Now add the most flexible and easy-to-use routing scheme and a huge array of inputs and outputs. Put it all into one beautifully crafted 2RU steel chassis and it's not just art, it's Summit Audio's ECS-410 Everest. Simply route from the Mz2 switchable tube-transistor preamp to the dual mode Dc1 dynamics module and try some sweet sounding LC passive EQ with the Fe1 EQ. Now send the signal to the switchable dual tube/high voltage transistor Db2 DriveBus output for added color, from subtle to intense, and route each section in and out with the touch of a single button with TouchPatch (tm), the original routing design from Summit Audio.

Each sections of the ECS-410 Everest has it's own balanced IO as well, so it really is like adding four complete products into your arsenal.

• Mz2 tube or solid state mic preamplifier
• +48VDC phantom power, polarity switch, HPF, pad, 10 segment LED meter
• Fe1 passive 3 band equalizer
• Switch selectable frequencies, +/-12dB per band, peaking/shelving, bypass
• Dc1 dual mode dynamics, "Tight" and "Classic" compression modes
• Sweepable gain, threshold, attack, release, bypass, stereo linking with 2 units, 10 segment LED meter
• Db1 DriveBus output, variable drive and output
• Tube/Solid State/Bypass, VU meter
• TouchPatch routing- 10 routing schemes at the touch of a button
• Each section has independent I/O
• Three 12AX7A/ECC83 vacuum tubes (one Mz2, two Db1)
• 4 complete units in one
• 3 Year Warranty
• Four XLR inputs, four XLR outputs, two 1/4" TRS outputs, side chain, stereo link, insert

Mz2 Microphone Preamplifier
• Max. Gain: +60dB (plus 20dB when routed through the Db2 DriveBus Output)
• THD+N: (@+30dB) 0.008% (A-weighted), 0.01% (unweighted)
• Max. Output: +25dB
• Freq. Response: Solid-state: 10Hz-300kHz +/- 2dB; 15Hz-200kHz +/- 0.5dB
-Tube: 10Hz-150kHz +/- 2dB; 15Hz-70kHz +/- 0.5dB
• Mic Impedance: 2K ohms
• Hi-Z Impedance: 10M ohms
• Type: Switchable between tube (12AX7A) or discrete transistor
• High Pass Filter: 60Hz at 6dB/octave
• Metering: 10 segment LED
• Phantom Power: +48 VDC
• Pad: -20dB
• Polarity: 0 or 180 degrees
• Inputs: Balanced XLR mic input; Front panel 1/4” Hi-Z input (unbalanced)
• Outputs: Balanced XLR +4dBu; -10dBV 1/4” TRS (nominal)

Fe-1 Passive 3 Band Equalizer
• THD+N: (@+4dB) (no cut or boost) 0.009% (A-weighted), 0.025% (unweighted)
• Freq. Response: 5Hz-100kHz +/- 0.5dB; 5Hz-200kHz +/- 2dB
• Frequencies:
- Low: 33, 60, 100, 150, 270, 390 Hz (peak or shelf)
- Mid: 560, 630, 1K, 1.6K, 2.5K, 3.3K Hz
- High: 5K, 7.2K, 8.2K, 10K, 12.5K, 16K Hz (peak or shelf)
• Cut/Boost: +/- 12dB per band
• Low Shelf: 6dB/8va, peaking bandwidth 2 octaves
• Mid Peaking BW: 2 octaves
• High Shelf: 6dB/8va, peaking bandwidth 2 octaves
• I/O: Balanced XLR, +4dBu, in and out

Dc1 - Dual Mode Compressor
• THD+N: (@+4dB) (no compression, but through gain cell) 0.025% (A-weighted), 0.041% (unweighted); (with 6dB compression) 0.013% (A-weighted), 0.022% (unweighted)
• Freq. Response: 5Hz-200kHz +/- 2dB; 5Hz-136kHz +/- 0.5dB
• Gain: -4dB to 10dB
• Attack: Variable from 4mS to 100mS
• Release: Variable from 50mS to 1S
• Ratio: Classic: 3:1, Tight: 10:1 (approximate, program dependent)
• Metering: 10 segment LED for gain reduction
• I/O: Balanced XLR, +4dBu in and out, 1/4” side chain jack, 1/4” stereo link jack

Db2 - Drive Bus Master Output and Overdrive
• THD+N: (@+4dB) Bypass: 0.002% (A-weighted), 0.008% (unweighted)
-Tube: 0.3% to overdrive (unweighted)
- Solid-state: 0.013% to overdrive (unweighted)
• Freq. Response: Tube:
- 5Hz-50kHz +/- 2dB; 5Hz-25kHz +/- 0.5dB
- Solid-state: 5Hz-200kHz +/- 2dB; 5Hz-130kHz +/- 0.5dB
• Gain: +20dB
• Type: Tube (12AX7A) or discrete transistor
• Metering: Analog VU output level
• I/O: Balanced XLR, +4dBu in and out; -10dBV 1/4” TRS out

Weight and Dimensions
• Size: 2RU, 19” x 3.5” x 17”
• Weight: 26 lbs

Power
• Power Requirement: 100VAC-240VAC
• (Note: Different fuse and switch positions for 100V, 115V and 240V)


[Back to search results]



Quick product links

Follow us on:

Follow ESV on Facebook   Follow ESV on Twitter

Join our mailing list

Add your email address below to subscribe:

  • Hear about breaking news and product announcements
  • Save money with the all latest offers!
For Sale. For Hire. For You.
© 2009 Eastwood (Sound and Vision) Ltd E&OE